+- Linux Lite Forums (https://www.freecinema2022.gq/forums)
+-- Forum: General (https://www.freecinema2022.gq/forums/forumdisplay.php?fid=4)
+--- Forum: Introductions (https://www.freecinema2022.gq/forums/forumdisplay.php?fid=12)
+--- Thread: How can I install Linux Lite by the very beginning? (/showthread.php?tid=6723)
Re: How can I install Linux Lite by the very beginning? - Moltke - 01-20-2020
(01-20-2020, 06:44 PM)Roken link Wrote: Wow, what a bad experience! I almost lost my pen drive! By the way, using Balena Etcher I almost lost my pen drive too.
I had to use "Diskpart" from CMD. I used the commands "list disk", "select disk and "Clean". After that I ran Rufus again using the first option. And now at least my pendrive is back live.
However I still am not able to install LL, even excluding step 3.
I think maybe the problem is the failure on constructing a bootable device, although Rufus said the procedure was concluded successfully.
[member=10760]Roken[/member], Are you using the same "not so old pendrive" that has repeatedly failed to boot time after time or the "old one" you said did succesfully booted the "windows for example"? I think you might give that a try and see how that goes.
Re: How can I install Linux Lite by the very beginning? - firenice03 - 01-20-2020
(01-20-2020, 04:33 PM)Roken link Wrote: firenice03,
I'm afraid your comment does not helped.
However I did research about UEFI since you said it´s like other kind of BIOS. And I find out I have BIOS not UEFI !!!
That´s why my BIOS don´t have the option to enable legacy bios as I told before, because it IS the legacy BIOS already.
About Etcher, are you assuming that is impossible to Balena Etcher fail ??
It's the same that saying all Linux O.S. is fully dependent on a third party software called Balena Etcher! If Balena Etcher fails no one never could be able to use Linux ever. That´s insane!
It does not help if you go this way and do not check others alternatives how to do that like I was trying to do.
I'm saying, saying it "It doesn't work" - doesn't help anyone trying to help you.
I'm assuming something is wrong - I'm trying to help figure out what...
You may be overthinking it. Have you found one that does create a bootable usb? if so, use that - yes they are all the same (except multiboots)...
I typically dont use etcher.... BUT Don't assume cause its not readable its failed... Try it, it may work
(01-19-2020, 07:50 PM)Roken link Wrote: Yep, I saw that Balena Etcher on the manual. This Balena Etcher just don´t work (by the way I almost lost my pendrive doing that!).
When I followed Balena Etcher procedure, it simply created an empty USB drive that Windows or the BIOS cannot read.
That is by design - Windows will not read it, its a boot disk now, as I mentioned in my previous post..
ARE you certain of your BIOS??
In a previous post you say... you disabled secureboot? - - That is available to UEFI.. not typically a bios...
(01-19-2020, 10:03 PM)Roken link Wrote: Yes, I disabled secure boot. It seems I don't have the option to enable legacy boot on my BIOS configuration. But the first boot is set to be my USB! It appears the fabrication name of my USB.
However, still Windows 10 is always started and no Linux Lite options is displayed.
If you haven't yet - Please try the UEFI version - it will install to either a BIOS or UEFI enabled systems --- a BIOS installer will only install to BIOS...
Don't give up [member=10760]Roken[/member]
If the PC is UEFI - BIOS LL will not install (you are correct it doesn't see/read it)
You haven't mentioned you PC model - it might help us point you in the right direction...?
You can also look in System Information (msinfo32 from run) for BIOS
![[Image: msinfo32-uefi-bios-mode.png]](https://www.easyuefi.com/images/resource/msinfo32-uefi-bios-mode.png)
Re: How can I install Linux Lite by the very beginning? - Nasmad - 12-28-2020
Hi,
I know that was a old post but maybe that could help someone.
I had the same problem and personaly that was just a corrupted iso.
So I downloaded it again and that's working for me.
Re: How can I install Linux Lite by the very beginning? - TheDead - 01-04-2021
LoL Nasmad... if that was the case here... the thread was a lot of wasted effort!
If not, maybe 5.x works now...
Re: How can I install Linux Lite by the very beginning? - MIKE STAN - 02-13-2021
Yep, I saw that Balena Etcher on the manual. This Balena Etcher just don´t work (by the way I almost lost my pendrive doing that!).
When I followed Balena Etcher procedure, it simply created an empty USB drive that Windows or the BIOS cannot read.
Re: How can I install Linux Lite by the very beginning? - Valtam - 02-14-2021
Try Rufus in Windows. Thread closed, please don't hijack other people threads. Start your own, thank you
